Table of Content
Once connected, go back to the Bell Smart Home app to complete the installation. On the next pages, you’ll be asked to confirm that the video doorbell has been mounted and the LED alternates between red and green. Feed the existing doorbell wires through the hole in the centre of the supplied doorframe mounting plate. Remove the two power wires from the existing doorbell button. This doorbell chime uses a speaker to play a doorbell sound. If you have a digital doorbell chime, you’ll need an adapter for your doorbell.
To ensure proper power-down sequence, wait a minimum of 20 seconds before installing new battery. Visit the manufacturer’s websiteUnder normal conditions the battery can last up to 2 years. If the battery is low, the trouble notification will be indicated on the control panel’s screen. Replace the old batteries with two CR2025 lithium batteries, with the plus (+) side facing down. Unpack the passive infrared sensor and remove the screw from the bottom housing.
Bell Smart Home – Video equipment installation guides
Test the unit by momentarily pressing one of the Transmit buttons. The LED should light up. Install the battery into the battery clips its orientation is the same as the one you just removed. Press in the snap and separate the cover from the base. Install the battery making sure its orientation is the same as the one you just removed. Most smoke detectors expire 10 years after the manufacturing date, and most carbon monoxide detectors expire after 6 years.
The Z terminal of the smart thermostat can currently control a third heating stage, a humidifier or a dehumidifier. Some systems rely on the thermostat itself to control the baffle. The smart thermostat will be able to support these systems using the Z terminal. Enter the user's first and last name and then touchCreate.
My AccountTV, phone and Internet
You can still arm and secure your system in other areas. Most panels are wall mounted . The following only applies if you requested your panel on a tabletop stand instead of having it mounted. Click on Video, Settings then Stream video to security panel screen.
Tighten the set screw located on the bottom of the video doorbell , being careful not to damage it . If you need to install a transformer, digital doorbell adapter or doorbell chime, we recommend that you use a qualified electrician. Power to doorbell must be turned off for these installations.
Bell Smart Home | Support and customer service
A $5/mo. Automation add-on is required for Good and Better packages. Failure to make the bracket flush on the wall could cause a poor power connection between the bracket and the doorbell camera. To ensure compatibility with your Bell Smart Home system, additional or replacement cameras must be purchased from Bell Smart Home. Ask about self and technician installation options when speaking with a Bell Smart Home representative.
Manuals.plus needs to review the security of your connection before proceeding. To protect from the weather, apply caulking or silicone sealant where the back of the junction box touches the mounting surface. To make holes for the Ethernet cable, use a 1/2 inch drill bit. Allow a few minutes for the PoE adapter/camera to connect with your modem.
IG glass break detector – GB1-345
You can purchase a digital doorbell adapter at an electronics store. Attach the camera to mounting plate and secure it with the provided base secure screw. Attach the mounting plate to the wall using the provided screws. Determine the path that the power cable will take from the camera location to where it will be plugged in.
To silence the alarm, press Cancel then enter your user code. When you’re hurt and unable to call out and alert others that you need help. Go to your system panel and set off the Auxiliary/Medical emergency panic. If your home is on fire, gather everyone up to exit immediately. Don’t even take time to look for your mobile phone. On the way out, trigger a Fire emergency with two quick taps on your panel.
4 Includes installation of standard equipment in the selected Bell Smart Home package (no additional equipment/feature). Add a video doorbell to see, hear and talk to whoever is at your door – perfect for home deliveries. With the Bell Smart Home app, you can manage user access settings for your system and locks. After the power-up sequence the green LED should blink about once every 12 seconds to indicate normal operation.
With a key or small screwdriver, press the black tab located at the bottom of the remote and slide the chrome trim off. Press the clip over the sensor to unlock the cover. Then, gently pull the cover to remove it. Severability; Assignment; Effective Date; Agreement.
Open the cap to reveal the screw. Insert the new batteries, making sure the orientation of the batteries is the same as the batteries that you just removed. Put the cover back on and attach with the screw.
No comments:
Post a Comment